What's new

Gimme the basics

Dissone

Postman
Joined
Oct 16, 2016
Messages
102
Scratching the itch I ordered a Pico squeeze and sxk hadaly and they are on the way from fasttech. Never owned a dripper before or a squonk.
I believe the the mod is unregulated, and will need to pay attention to ohms and battery safety.

Questions:-

Sensible build for hadaly. Ohms and how many watts?
How much/often do I need to squeeze the bottle?
How willl I know when to squeeze?
Does the bottle need to be kept full, or will it suck up all the juice?
Other than my nic base all my juice is vg, will this make it harder for the juice to reach the atty?

Thanks
 
1. Too early to check
2. Every 3 or 4 pulls
3. Less flavour/vapour/dry hit!
4. It will take most of the bottle before you need to refill it
5. Not noticed any issues (our DIY is 90% vg)

With squonking start by having the top cap off the hadaly so you get used to seeing how long you have to squeeze the bottle fore before the wick is soaked. You will get used to it in no time.
 
Aye, the Squeeze is mostly mechanical, there is a wee thingy that limits the power output to about 50ish watts.
Cracking bit of kit tho'!

Hadaly, well, my one has a 0.5 ohm, 24 gauge flattened Nichrome build in it and it works finest kind.
A larger coil is better in the Hadaly due to the nature of the build deck and the way the air comes in. This makes life slightly easier for you if you've no built a coil before.
Watch a few review videos on the H and see what others put in it. You will spend a bit of time experimenting to get your sweet spot.
And get some Nichrome wire for using in it too. As it is lower resistance wire it is perfect for mechs like the Squeeze to get a good vape.

The wee besom above, :p, should also have advised you getting a couple of spare bottles for the mod.....
 
1. Too early to check
2. Every 3 or 4 pulls
3. Less flavour/vapour/dry hit!
4. It will take most of the bottle before you need to refill it
5. Not noticed any issues (our DIY is 90% vg)

With squonking start by having the top cap off the hadaly so you get used to seeing how long you have to squeeze the bottle fore before the wick is soaked. You will get used to it in no time.

Thanks, this was what I was kind of expecting. Good idea regarding the top cap.
 
Aye, the Squeeze is mostly mechanical, there is a wee thingy that limits the power output to about 50ish watts.
Cracking bit of kit tho'!

Hadaly, well, my one has a 0.5 ohm, 24 gauge flattened Nichrome build in it and it works finest kind.
A larger coil is better in the Hadaly due to the nature of the build deck and the way the air comes in. This makes life slightly easier for you if you've no built a coil before.
Watch a few review videos on the H and see what others put in it. You will spend a bit of time experimenting to get your sweet spot.
And get some Nichrome wire for using in it too. As it is lower resistance wire it is perfect for mechs like the Squeeze to get a good vape.

The wee besom above, :p, should also have advised you getting a couple of spare bottles for the mod.....

0.5 is good for me as I mostly build in the 0.3 - 0.5 range.
I'm used to building coils as all of my atties are rebuildable.
I have some N80 wire on order but not 24 gauge flattened - think it may be flapton?
And I preempted the need for spare bottles and have them arriving with the mod.
Thanks
 
0.5 is good for me as I mostly build in the 0.3 - 0.5 range.
I'm used to building coils as all of my atties are rebuildable.
I have some N80 wire on order but not 24 gauge flattened - think it may be flapton?
And I preempted the need for spare bottles and have them arriving with the mod.
Thanks
It's a flexible bugger. I've got three set up in mtl mode with builds around 1.2 ohms and one with a 0.5 s'steel 26 awg loaded hadaly. The mod has a flashing light system like an old ego pen. So it lets you know the rough level of your battery and when it's time to charge. Plus it has a short breaker. Love mine.
 
It's a flexible bugger. I've got three set up in mtl mode with builds around 1.2 ohms and one with a 0.5 s'steel 26 awg loaded hadaly. The mod has a flashing light system like an old ego pen. So it lets you know the rough level of your battery and when it's time to charge. Plus it has a short breaker. Love mine.

Thanks for this, sounds like it should be good.
I remember those battery's with the dreaded orange flash - getting my first 18650 mod was as game changing as getting my first car with power steering.
Think I'm going to enjoy something new.
 
With the hadaly it is quite easy to over squonk as it has bottom air flow holes so you'd need to keep an eye on it. I build at around 0.5-0.6 ohms on it. The squeeze is a great little mod though [emoji2]
 
With the hadaly it is quite easy to over squonk as it has bottom air flow holes so you'd need to keep an eye on it. I build at around 0.5-0.6 ohms on it. The squeeze is a great little mod though [emoji2]

The pico and hadaly both arrived today and I can see what you mean with the bottom airflow. Once my flat wire arrives I can get a build in it. I can start off like Miss pepper suggested and leave the cap off to get an idea. Come on postie!!
 
It's a nice atty, once you've had a play look at the goon 22mm on fasttech (you'll need a bf pin also available on fasttech) then you can try a couple of dual coil builds and the airflow is a lot higher [emoji3]
 
Back
Top Bottom