Tube Mods Getting Neglected :C

[Smut]

Been pushing my tubes to one side in favour of parallel or series boxes, I just cant seem to lock down a decent warm build they all ways come out cooler and underwhelming. So I need some ideas or recommendations for some builds to try out

Thanks!!

Edit: Preferably dual coil had a couple single coil builds that were all right but prefer dual coil builds

 

[EmbraSewerRat]

Been pushing my tubes to one side in favour of parallel or series boxes, I just cant seem to lock down a decent warm build they all ways come out cooler and underwhelming. So I need some ideas or recommendations for some builds to try out

Thanks!!

Edit: Preferably dual coil had a couple single coil builds that were all right but prefer dual coil builds

You tried using Nichrome or 316 stainless steel for your mech builds?
Dual 0.4mm Nichrome, 6/7 wraps with 2.5mm id goes well for me.
Or a cheeky 0.4mm Nichrome cored fused Clapton.

Keep in mind that a single tube isna going to wallop the same as certainly a series box. If memory serves you can build really low ohm builds on a parallel which isna really recommended for a single battery tube. So, your experience isn't going to be the same.

 

[Smut]

You tried using Nichrome or 316 stainless steel for your mech builds?
Dual 0.4mm Nichrome, 6/7 wraps with 2.5mm id goes well for me.
Or a cheeky 0.4mm Nichrome cored fused Clapton.

Keep in mind that a single tube isna going to wallop the same as certainly a series box. If memory serves you can build really low ohm builds on a parallel which isna really recommended for a single battery tube. So, your experience isn't going to be the same.

90% of the time i use nichrome unless im trying to get the resistance higher then ill you kanthal.

Stole @mattvapes1976 tube build which seems to be working a treat, 28g aliens paralleled to with 26g

 

[itsher]

My go to builds for mechs, please use good batteries and Vape sensibly (have to say that really). 21awg NiFlat from flatwire, 5 wraps over 3mm ID Dualled. Or my current favourite, 20awg Anarchist wire, 6 wraps 3.5mm ID Dualled and comes in around 0.10 ohms and is very flavourful. The key also, good cotton that is heat resistant and keeps up, Fuzion cotton, you get a tonne and it's a good product. I Vape mechs and RDAS all day every day. [emoji108]

 

[Smut]

My go to builds for mechs, please use good batteries and Vape sensibly (have to say that really). 21awg NiFlat from flatwire, 5 wraps over 3mm ID Dualled. Or my current favourite, 20awg Anarchist wire, 6 wraps 3.5mm ID Dualled and comes in around 0.10 ohms and is very flavourful. The key also, good cotton that is heat resistant and keeps up, Fuzion cotton, you get a tonne and it's a good product. I Vape mechs and RDAS all day every day.

Every time ive tried yo go back to marco coils they just seem meh, they just lacking something compared to aliens or staggered staples

 

[wraith]

I tend to go for 5 wraps 26awg kanthal claptoned with 34awg nichrome and paralleled with 4 wraps 28awg kanthal on a 2.5mm screwdriver.

Comes out about 0.25ohm and gives a nice vape without too much ramp-up.

 

[Smut]

I tend to go for 5 wraps 26awg kanthal claptoned with 34awg nichrome and paralleled with 4 wraps 28awg kanthal on a 2.5mm screwdriver.

Comes out about 0.25ohm and gives a nice vape without too much ramp-up.

Will try that and see how it works out

 

[wraith]

Will try that and see how it works out

Should have made it clear that that's dual coil.

Let us know how you find it.

 

[chimerax]

I either build 2.5mm 26g parallel dual coil ni80 7 wraps which is around 0.18 ohms or 2.5mm 26/35g fused claptons dual coil ni80 6 wraps at about 0.15 ohms if I'm using VTC5s. Depending on the RDA that's a nice warm vape with plenty of flavour and they heat up pretty fast. And most importantly, they are both piss easy to build yourself.

That build on a Tsunami is down right toasty, but on something like the Phenotype-L it's a lot cooler, so your choice of RDA makes a huge difference.