Getting vape liquid in mouth.

[Ryan Brown]

I'm quite new at vaping and just got a new mesh pro tank. I can't seem to set it to stop it feeling like liquid is coming through the spit tip. Is there a way to fix this?

 

[Mr Ripple]

I'm quite new at vaping and just got a new mesh pro tank. I can't seem to set it to stop it feeling like liquid is coming through the spit tip. Is there a way to fix this?

Are you putting enough power through it?
It sounds like the juice is not being vaporized enough.
What wattage are the coils rated at? and what watt have you got your mod set up at?

 

[MrDJ]

I'm quite new at vaping and just got a new mesh pro tank. I can't seem to set it to stop it feeling like liquid is coming through the spit tip. Is there a way to fix this?

Hi and welcome to the Planet.

need a bit more info.
so you have the freemax mesh pro which is a great tank and i have 2 of them and never had this issue.
normally liquid through the mouthpiece is a flooded coil.

so which coil are you using. at what wattage, with what make and ratio of juice vg/pg and is it a 2ml tpd tank or the larger 6/7ml
do you prime the coil by dripping a few drops of juice on all the cotton around the coil and then filling the tank. and then are you starting at a low wattage and turning up every few puffs.

 

[Ryan Brown]

It's just a 2ml tank but with the bubble glass, it's a double coil recommended at 60-90. Moved up watts and sat on 61, primed the coil as well. I turned down the ohms after some reading which seems to of reduced it but still feel the it on the back of my teeth. Using ruthless grape drank 100ml it 1.5 shots of nicotine. Not 100% on the terminolgy for everything so hope this makes sense. Thank you

Hi and welcome to the Planet.

need a bit more info.
so you have the freemax mesh pro which is a great tank and i have 2 of them and never had this issue.
normally liquid through the mouthpiece is a flooded coil.

so which coil are you using. at what wattage, with what make and ratio of juice vg/pg and is it a 2ml tpd tank or the larger 6/7ml
do you prime the coil by dripping a few drops of juice on all the cotton around the coil and then filling the tank. and then are you starting at a low wattage and turning up every few puffs.

 

[Ryan Brown]

Are you putting enough power through it?
It sounds like the juice is not being vaporized enough.
What wattage are the coils rated at? and what watt have you got your mod set up at?

Recommended at 60 - 90 and moved up to 61 currently. I have tried going up to 70 but catches my throat.

 

[Mr Ripple]

Recommended at 60 - 90 and moved up to 61 currently. I have tried going up to 70 but catches my throat.

I'd say turn it up a little more and puff it a bit harder to draw more air over the coils.

 

[uyir222]

Are you possibly over priming the coil?

Are you possibly maybe dragging to hard on the drip tip pulling up the juice to fast before the juice has a chance to fully vapourize?

Hope you manage to find the solution ,

 

[EmbraSewerRat]

Recommended at 60 - 90 and moved up to 61 currently. I have tried going up to 70 but catches my throat.

Might have a bit too much nic in for that power level, 70W with a ~4.5% nic - ooh nippy sweetie time!

Mesh will take a lot of power so any less than say 65W and you'll get drips of liquid in your mouth.
Crank down the nic and go a bit clarkson on the power levels.

 

[tony68]

Vape through it. Up the power. This is where you gain experience. Gotta take the crap before you know what works. Its a learning curve that never stops. But if you find your vape you will know.

 

[wackygt]

I had a similar issue with the U-force tank - for my issue it was case of dragging less hard as I was pulling through more liquid than the coil could handle.

As you are vaping within the coil wattage range, that shouldn't be the issue, however increasing it to 65 watts couldn't hurt.

Also - are you using the stock drip tip that came with it? Another rookie error I made when I started sub ohming was fitting a narrow bore drip tip - again this contributed to pulling the liquid through at a higher pressure than the coil could handle.