Vape burn coils instantly

[elanto]

Hello everyone,
I have been using my Vaporesso Xross Nano perfectly for about a month, but suddenly my vaper is burning the new coils on the first puff.
I have used an old coil, with more than 1200 puffs and it works perfectly. The new one I bought burned on the first puff, I bought a new one and the same thing happened. I bought a new coil again in another store and the same thing, burned on the first puff.
I want to emphasize that I use the same liquid as always and the same coils that I have been using previously, in addition I have followed all the recommendations so that they do not burn, even waiting for the third half hour for it to soak before using it.
I am desperate, I do not understand why this can be happening.
I would appreciate any help, thank you very much and greetings.

 

[Mitz]

Welcome to the forum

Can't help with your coil issues, but I'm sure someone will be along soon to offer some advice.

 

[Richard Winter]

Hello everyone,
I have been using my Vaporesso Xross Nano perfectly for about a month, but suddenly my vaper is burning the new coils on the first puff.
I have used an old coil, with more than 1200 puffs and it works perfectly. The new one I bought burned on the first puff, I bought a new one and the same thing happened. I bought a new coil again in another store and the same thing, burned on the first puff.
I want to emphasize that I use the same liquid as always and the same coils that I have been using previously, in addition I have followed all the recommendations so that they do not burn, even waiting for the third half hour for it to soak before using it.
I am desperate, I do not understand why this can be happening.
I would appreciate any help, thank you very much and greetings.

There are 4 different versions of the Xros Nano. The older versions have fixed adaptive wattage but the later ones have adjustable wattage. All the pods for the Xros Nano have integrated coils which are non replaceable.

Depending on which version you have, if its adjustable wattage then fill up a new pod, let is stand for 15 minutes and set the wattage to its lowest setting and take a few draws to pull eliquid through the coil/pod. Increase the wattage slowly, each time taking a few draws until you reach your desired wattage.

If it's still giving you a burnt taste then it must be faulty pods. Hope this helps.

 

[John R]

Only two things spring to mind, either the pods are of dubious quality or the way you are filling it is airlocking them.

The former you have no control over, the latter you can take a few draws through the pod to try to clear any lock, then put it in the device after a few minutes.

You can tell if it's been airlocked as the liquid level will go down without even heating it in a device.

 

[elanto]

Welcome to the forum

Can't help with your coil issues, but I'm sure someone will be along soon to offer some advice.

Thank you!

 

[elanto]

There are 4 different versions of the Xros Nano. The older versions have fixed adaptive wattage but the later ones have adjustable wattage. All the pods for the Xros Nano have integrated coils which are non replaceable.

Depending on which version you have, if its adjustable wattage then fill up a new pod, let is stand for 15 minutes and set the wattage to its lowest setting and take a few draws to pull eliquid through the coil/pod. Increase the wattage slowly, each time taking a few draws until you reach your desired wattage.

If it's still giving you a burnt taste then it must be faulty pods. Hope this helps.

You mean that I should do it in eco mode?

 

[elanto]

Only two things spring to mind, either the pods are of dubious quality or the way you are filling it is airlocking them.

The former you have no control over, the latter you can take a few draws through the device to try to clear any lock, then put it in the device after a few minutes.

You can tell if it's been airlocked as the liquid level will go down without even heating it in a pod.

I will take your advice and let's see. Thanks!

 

[Infinium]

Vaporesso Xross Nano

Lately, I've been hearing about many issues with Vaporesso coils. I don't know if, like Aspire, low-quality fake products have started circulating.

Besides priming the coil for 15 minutes, if your device has adjustable wattage, try vaping at 2-4 watts lower than the minimum for the first ml of liquid.

 

[MTB Vaper]

Its hear say but I think people are having problems the 3ml pods. On my Nano 3 never had an issue with the 2ml 0.8 pods and 50/50 liquid.

 

[Richard Winter]

You mean that I should do it in eco mode?

If it has an eco mode that reduces the wattage to the new coil I'd suggest having it on that setting for a good dozen draws to bed the coil in before you hit it with higher power.