BP Mods TMD Boro Community Review

[eyeball kid]

Tyvm for that feedback.

In your opinion, what are the best coils between VC, PNP and TMD if you had the chance to try them too (on the TMD)?

I had exactly the same experience with the shift boro, the joint between the base and the glass container seemed crooked, I have never had so many leaks, it also had difficulty passing through the Tycoon because of the ring airflow wider than the base (I had completely removed the ring to "correct" this problem), it was very tight, perhaps the fact of forcing deformed the ato or it is simply of poor quality, the only good news is that with the purchase of the shift I ordered coils with it, so I am VC coils 0.4ohm ready for the TMD lite.

Where did you find your new BP ?

The vaporesso and GTX coils are excellent but both do drip a little from the base after use, voopoo seem slightly better. The vc coils are excellent but they need soaking in the tank for a good ten minutes first and run them at half the wattage for a little while, slowly turning up. I think it's the pulp wick, takes a while to work at top efficiency but once they do I think they have the best flavour and longest life. Just my experience. They have the bp lite still at legion of vapers for a good price. I've not seen any OG tmd's for a while. Swings and roundabouts really. The og one's have the sponges but the lite ones offer the two tanks with different fill port sides.

 

[Atyos]

The vaporesso and GTX coils are excellent but both do drip a little from the base after use, voopoo seem slightly better. The vc coils are excellent but they need soaking in the tank for a good ten minutes first and run them at half the wattage for a little while, slowly turning up. I think it's the pulp wick, takes a while to work at top efficiency but once they do I think they have the best flavour and longest life. Just my experience. They have the bp lite still at legion of vapers for a good price. I've not seen any OG tmd's for a while. Swings and roundabouts really. The og one's have the sponges but the lite ones offer the two tanks with different fill port sides.

Ty, i think the one without the sponges and with the side opening tank is the lite V2, maybe condensation does not exists anymore on this one so pads are not needed, i purchased mine on HealthCabin, it's on his way, i will make you a feedback after 1-2 weeks of use.

 

[eyeball kid]

Ty, i think the one without the sponges and with the side opening tank is the lite V2, maybe condensation does not exists anymore on this one so pads are not needed, i purchased mine on HealthCabin, it's on his way, i will make you a feedback after 1-2 weeks of use.

Hope your one has arrived. Had the non sponge one for a while. The side open tank is useful for mods like the tycoon but I can assure you, wherever a one or gtx style coil is use, there will always be juice loose, lol.

 

[Atyos]

Hope your one has arrived. Had the non sponge one for a while. The side open tank is useful for mods like the tycoon but I can assure you, wherever a one or gtx style coil is use, there will always be juice loose, lol.

Mine is not here yet it's from china, Will get it soon i think. Is this really Juice loose or condensation ?

 

[eyeball kid]

Mine is not here yet it's from china, Will get it soon i think. Is this really Juice loose or condensation ?

Bit of both. Condensation is always an issue. Hot coils in a cooler climate, but the pnp/gtx style coils with flat bottoms have a nylon separator between the centre positive contact and surrounding negative. As the coil heats and cools it compresses the separation insulator and it will never really return perfectly so they tend to seep a tiny bit. Sometimes annoyingly more than a tiny bit. Always been that way. The vc one's seem least leaky for me but it's just a case of cleaning the bottom of the coil in the boro if you see any seeping.

 

[Atyos]

Bit of both. Condensation is always an issue. Hot coils in a cooler climate, but the pnp/gtx style coils with flat bottoms have a nylon separator between the centre positive contact and surrounding negative. As the coil heats and cools it compresses the separation insulator and it will never really return perfectly so they tend to seep a tiny bit. Sometimes annoyingly more than a tiny bit. Always been that way. The vc one's seem least leaky for me but it's just a case of cleaning the bottom of the coil in the boro if you see any seeping.

maybe with a thicker juice like 70/30?