Frame staple alien in the the Odd Job

[MTB Vaper]

Fitted a n80 2.5mm frame staple in the Odd Job, so far vaping alot better then the little fused Clapton I was using. Ramps up quicker and heat doesnt build up.

 

[Moses]

Fitted a n80 2.5mm frame staple in the Odd Job, so far vaping alot better then the little fused Clapton I was using. Ramps up quicker and heat doesnt build up.View attachment 362505

What's it ohming out at?

 

[MTB Vaper]

What's it ohming out at?

0.35ohm, I've taken the odd jobs adjustable airflow ring off as it does add a bit of restriction.
It's not a normal frame staple, stacked different.

 

[Moses]

0.35ohm, I've taken the odd jobs adjustable airflow ring off as it does add a bit of restriction.

I've taken both mine off, I do find a simple fused Clapton is a bit small inside it. I may look at what else I have laying around and chuck something bigger in mine. What wattage you running that at? As I only normally like to go to around 25watts unless it's a mech Boro

 

[MTB Vaper]

I've taken both mine off, I do find a simple fused Clapton is a bit small inside it. I may look at what else I have laying around and chuck something bigger in mine. What wattage you running that at? As I only normally like to go to around 25watts unless it's a mech Boro

I'm upto 40w I like to hit the odd job V1 really hard. No heat issues with the coil would handle alot higher. It's a low mass coil inside the alien outer.

 

[vapervince]

Did you wrap the coils yourself ? I`m a relative newcomer to AIO vaping and still finding my way, so far I`m getting the best flavour from a 2 core clapton bought in from Wotofo but I know it can be better, I find the biggest limitation for me anyway, is the restricted air flow, but again I might not be buying the best tank / RBA to get the most out.

 

[MTB Vaper]

Did you wrap the coils yourself ? I`m a relative newcomer to AIO vaping and still finding my way, so far I`m getting the best flavour from a 2 core clapton bought in from Wotofo but I know it can be better, I find the biggest limitation for me anyway, is the restricted air flow, but again I might not be buying the best tank / RBA to get the most out.

No Flying Custard coils sent it me as a test sample. I only really use the Sturdy one(clone) rba with 4mm air pin and the odd job fully open. Have a Ether rba setup for MTL as I didnt like it for RDL. Got 3 boro setups wont be getting anymore, think I'm done now I have the two rba's I like.

 

[vapervince]

No Flying Custard coils sent it me as a test sample. I only really use the Sturdy one(clone) rba with 4mm air pin and the odd job fully open. Have a Ether rba setup for MTL as I didnt like it for RDL. Got 3 boro setups wont be getting anymore, think I'm done now I have the two rba's I like.

Thanks, I`ve looked through my usual suppliers and cant find that brand, any idea where they sell em? I`ve got a couple of Ether RBA and a couple of VC Blaze and I know from using the same juices in drippers and RTA that the flavour can be better, it`s like going back to when I first started rebuilding, I know it can be better, kinda like an itch I`ve got to scratch.

EDIT - OK found him

 

[MTB Vaper]

Gone upto 55w without any heat issues, but using Aromaxy Lime Fizz juice 45w vapes just as good so sticking to 45w for the whole bottle.
I have a tub of Flying Custard RDL 2.5mm N80 aliens 3x30/40 to try in the Sturdy one at some point but that has 2.5mm SFC currently.