mech questions

[m4inbrain]

I've always had the jfc wide open on all my kayfuns. Rather than adjusadjusting the jfc I prefer to adjust my wicking with a bit more cotton for thinner juices. Siren 2 is also a great tank. Very good flavour. I haven't had any leaking issues but I know a few on here have.

As for coil choice, I use fused claptons or simple single strand micro coils. 26 or 28 gauge. The mtl fused claptons I use are 2 x 30ga / 38ga.

The Siren 2 can absolutely be a great tank, if you get the wicking just right. It's very unforgiving to wick, too little cotton just by a little bit and you get a mess, a little too much cotton and the flavour takes a walk. My (auth) Prime, i just throw a micro coil in there (28g 5-6wrap, depending on mood) and "some amount of cotton", and it always performs with no leaks. The fused claptons you use, do you wrap them off a spool of VV MTL Wire? What do they ohm out at?

I actually never used exotics in my MTL tanks, quite intrigued how that goes.

Absolutely love my Mod 101, looks great with any 22mm atty on top.

Yeah, very smart looking device - i'll certainly pick one up eventually. First now though, gotta replace my Invoke 220 - as i said yesterday, tried to do a few builds on it in a Radar RDA. Which, because i'm stupid, still had the squonk pin installed. Leaked all through the 510 into the mod, trying to figure out now if the batteries are still good to use and how to clean them. They smell great now though.

 

[Mitz]

The Siren 2 can absolutely be a great tank, if you get the wicking just right. It's very unforgiving to wick, too little cotton just by a little bit and you get a mess, a little too much cotton and the flavour takes a walk. My (auth) Prime, i just throw a micro coil in there (28g 5-6wrap, depending on mood) and "some amount of cotton", and it always performs with no leaks. The fused claptons you use, do you wrap them off a spool of VV MTL Wire? What do they ohm out at?

I actually never used exotics in my MTL tanks, quite intrigued how that goes.

Never had that experience myself with the Siren. But I spend half my life wicking one tank or another.

I use vv spool. 2.5mm 6 wraps comes out around .7.

 

[m4inbrain]

Cheers, gonna give that wire a go then too.

edit: @Mitz, stainless or Ni80? I'd assume Ni80?

This one?

https://www.wireandstuff.co.uk/prod...--3-Metre--10---Spool-by-Vandy-Vape-1405.html

 

[Mitz]

Cheers, gonna give that wire a go then too.

edit: @Mitz, stainless or Ni80? I'd assume Ni80?

This one?

https://www.wireandstuff.co.uk/prod...--3-Metre--10---Spool-by-Vandy-Vape-1405.html

Yeah, Ni80.

SS is too low resistance for my liking in MTL setups.

 

[greenbrucelee]

I am gonna pick that up. I prefer Ni80 or ss316L/430. I hate Kanthal it tastes like crap to me. This will be only non DNA mod

 

[greenbrucelee]

should i go for the 25a battery or 30a? ps they have released an updated one which take 21700 batteries.

 

[Mitz]

should i go for the 25a battery or 30a? ps they have released an updated one which take 21700 batteries.

What mod are you getting? And which batteries are you looking at?

 

[greenbrucelee]

I was gonna go for the vapecell 20700 either 25a or 30a as my coils are usuall around .2ohms

 

[Mitz]

I was gonna go for the vapecell 20700 either 25a or 30a as my coils are usuall around .2ohms

Then go for the 30 amp.

 

[greenbrucelee]

Then go for the 30 amp.

I can only find one place in the UK that has it at the minute for 26 quid but its on fast tech for 16 dunno if the ten quid difference is worth a three week wait.