HCigar SS Nemesis help ...

[ill_dawg]

I've only ever had misfired if the bottom pin wasn't down tight. I use 18350 flat tops, 18490 nipple tops, and 18650 flat tops without any rattle. Post a photo of your setup and we'll be able to help you get it firing right.

 

[Audiopsyence]

I reckon it's the 18500s, some are just too short. That screw in the bottom (switch) should be screwed all the way down. Try 350s or 650s or buy the hybrid kit* to successfully use the 500s.


8 Bit Vape had them in the uk, FT if you're willing to wait. It's the four piece (510 threaded) one you want.

 

[Audiopsyence]

I give up!

Spent the last few days trying different combinations of battery and atomiser. Switched between spring and magnet switch and still can't get it to work consistently.

I'm more than willing to take a look at it if you're really wanting to go down that route.

 

[Mostly]

I give up with this chaps postings. What made you think a mech was the way forward, and surely you have a camera phone.

 

[Van De Rooster]

I give up with this chaps postings. What made you think a mech was the way forward, and surely you have a camera phone.

I have a camera phone. I also have a 48 hour week and 2 kids. As I have a Vamo I've been using that in between trying to get the Nemesis to work. I have taken photos, but to be honest all they show is a Nemesis and three different size EFest batteries.

I wanted a mech as I was looking for something that would allow to experiment with different coils, as my Vamo won't fire low Ohm coils. If it was a bit smaller than the Vamo that would also be an advantage.

I'll try and post the pictures later if I get a chance, but I'm off to watch the cycling, spend time with my wife & kids. If I get a spare moment I may go online but I'm not on here every day.

 

[Blackhack]

There's seven members here (so far) who are trying to help you sort it out....

I'll try and post the pictures later if I get a chance, but I'm off to watch the cycling

If I get a spare moment I may go online but I'm not on here every day.

It takes two to tango mate.......

 

[Danny K]

I find on mine when I unscrew the body to replace a battery the top screw (atomiser end) unwinds with it a few turns and consequently when new battery go in there's no connection.
Also with flat top 18650 I need to unwind the bottom screw a few turns to make the connection.

Just a few suggestions maybe he has already tried these but were all here to try and assist.



Sent from my GT-N7105 using Planet of the Vapes mobile app

 

[Van De Rooster]

There's seven members here (so far) who are trying to help you sort it out....





It takes two to tango mate.......

And I appreciate the help, I really do.

If someone feel they no longer want to help that's fine, they can just stop replying. No need for snide comments. I only pointing out that I don't spent all day on here.

 

[Miss Pepper]

And I appreciate the help, I really do.

If someone feel they no longer want to help that's fine, they can just stop replying. No need for snide comments. I only pointing out that I'm don't spent all day on here.

We just want pics of your set up and batteries so we can help you.

Its easier for us to see what you are doing / working with to get you up and running

 

[Blackhack]

I wasn't going to reply to this.....

No need for snide comments.

but, I think I should.......First of all...It's not a snide comment.....You've asked for help, there's a good few who have tried to assist you with your problem, but it appears that you're too busy to add a couple of photos, or describe the problem in it's entirety....you might pop back later to see who might have posted a solution to your problem ??.....It's a disservice to the members here who are trying to help you if you're too busy to add a couple of photos and those members who have tried to assist you so far deserve at least, your own commitment to resolving your problem.........


I don't do Snide comments, but i do tell it like it is.....