Innokin pro on a drag 3

[Startrek]

I am new here Can anyone help me The innokin pro does not seem to like the drag 3 All the usual preparations done properly Burnt out 3 coils within seconds It’s ok with an ordinary innokin The first one Any advise would pick really appreciated thank you in advance

 

[LordOdin]

Burnt out Coils usually means to high wattage or not enough juice, you should prime your coils then add the juice to your tank, leave it to stand for 10 minutes so the coil is ready to vape, start at a low wattage then slowly raise it up to the wattage you want. Try and stick to the recommended wattage of the coil or maybe a bit lower.

EDIT:- Welcome to POTV

 

[MrDJ]

Hi @Startrek and welcome to the planet.

ive not used this kit or tank so a bit more info is needed.

did you buy the drag 3 as a kit which came with a tank? this tank is a direct to lung sub ohm tank for higher wattage.
the coils for that tank are rated at:
TPP-DM1 0.15Ω: 60 - 80W
TPP-DM2 0.2Ω: 40 - 60W

are you now using the innokin pro which im guessing is the zenith pro? if so this is a mouth to lung tank for much lower wattage.
these coils are rated:
1.2Ω （10-14W）
1.0Ω （20-25W)

so have you lowered your wattage on your drag 3

also what setting have you got the drag 3 set too. you need wattage mode also known as power mode. you should never use TC temperature control mode with these coils.

last thing. what ratio of juice are you using ie VG and PG
for sub tanks at higher wattage you are best with 70vg
for mouth to lung tanks at lower wattage you should be using 50vg/50pg as 70vg is too thick and will burn coils out quick.

as said above, priming any coil by dripping a couple of drops on all the cotton around the coil holes first, then install into tank, fill, sit for 5-10 mins then use the lowest wattage for the ohm coil you are using then turn up a watt every few puffs.

more info here
https://www.ecigarettedirect.co.uk/voopoo-drag-3-kit
https://www.innokin.com/zenith-pro

 

[ADDicT]

Hi and welcome

 

[gary68]

I am new here Can anyone help me The innokin pro does not seem to like the drag 3 All the usual preparations done properly Burnt out 3 coils within seconds It’s ok with an ordinary innokin The first one Any advise would pick really appreciated thank you in advance

@Startrek

 

[Startrek]

Hi @Startrek and welcome to the planet.

ive not used this kit or tank so a bit more info is needed.

did you buy the drag 3 as a kit which came with a tank? this tank is a direct to lung sub ohm tank for higher wattage.
the coils for that tank are rated at:
TPP-DM1 0.15Ω: 60 - 80W
TPP-DM2 0.2Ω: 40 - 60W

are you now using the innokin pro which im guessing is the zenith pro? if so this is a mouth to lung tank for much lower wattage.
these coils are rated:
1.2Ω （10-14W）
1.0Ω （20-25W)

so have you lowered your wattage on your drag 3

also what setting have you got the drag 3 set too. you need wattage mode also known as power mode. you should never use TC temperature control mode with these coils.

last thing. what ratio of juice are you using ie VG and PG
for sub tanks at higher wattage you are best with 70vg
for mouth to lung tanks at lower wattage you should be using 50vg/50pg as 70vg is too thick and will burn coils out quick.

as said above, priming any coil by dripping a couple of drops on all the cotton around the coil holes first, then install into tank, fill, sit for 5-10 mins then use the lowest wattage for the ohm coil you are using then turn up a watt every few puffs.

more info here
https://www.ecigarettedirect.co.uk/voopoo-drag-3-kit
https://www.innokin.com/zenith-pro

Hi @Startrek and welcome to the planet.

ive not used this kit or tank so a bit more info is needed.

did you buy the drag 3 as a kit which came with a tank? this tank is a direct to lung sub ohm tank for higher wattage.
the coils for that tank are rated at:
TPP-DM1 0.15Ω: 60 - 80W
TPP-DM2 0.2Ω: 40 - 60W

are you now using the innokin pro which im guessing is the zenith pro? if so this is a mouth to lung tank for much lower wattage.
these coils are rated:
1.2Ω （10-14W）
1.0Ω （20-25W)

so have you lowered your wattage on your drag 3

also what setting have you got the drag 3 set too. you need wattage mode also known as power mode. you should never use TC temperature control mode with these coils.

last thing. what ratio of juice are you using ie VG and PG
for sub tanks at higher wattage you are best with 70vg
for mouth to lung tanks at lower wattage you should be using 50vg/50pg as 70vg is too thick and will burn coils out quick.

as said above, priming any coil by dripping a couple of drops on all the cotton around the coil holes first, then install into tank, fill, sit for 5-10 mins then use the lowest wattage for the ohm coil you are using then turn up a watt every few puffs.

more info here
https://www.ecigarettedirect.co.uk/voopoo-drag-3-kit
https://www.innokin.com/zenith-pro

Thank you for your advice I use a innokin and drag 3 I have prepped the tank and coil as said above I have been using the innokin zlide with no problem on the drag 3 I like to try different things and learn new ways of vaping I really like the innokin pro It’s a really well built tank I usually vape the salt juices Which are low wattage as you will know I still have a lot to learn But as to why the pro keeps burning coils when lesser tanks don’t Is beyond me Thank you for all the advice