MTL RTA tank

[fentribal]

For ease of building and a good all-around vape, I would have to say the Vandy Vape Berserker Mini V2 would be a good choice.

 

[Crispycritters]

Thank you for your reply.
I was looking for a pre made coils and I find on Manabush website Vandy Vape
10 x 0.74Ohm Fused MTL Clapton Coils are they 0.7? And where I can found the range of wats to use, usually It’s on the stock coil packet . 10-15 w?
Also this coils is 2.5 mm and I learn here from some kind person who explained me about the cotton, that I will buy shoelaces pre made cotton for 2.5 mm.
I will start with the pre made coils but I ideally would like to have a master class with someone who knows all about it to learn how to make them my own, as I don’t want to blow up the whole lot . I am really don’t understand them ohm to wattage etc.

When it comes to coils for rebuildables the wattage isn't as critical, I suggest you start at around 12 Watts and slowly raise the wattage if you find it doesn't give enough vape or is too cool a temperature until you find your preference. As a rough guess I'd say somewhere in the 12 to 16 Watt range would suit most MTL vapers but you can go higher if you like a higher powered lose MTL. With rebuildables it's not a complete loss if you overdo it slightly - you may scorch the cotton if you go OTT, but its highly unlikely you'll damage the coil - only the cotton needs replacing, unlike a stock coil when any hint of burnt cotton means you have to bin it.

 

[Eka]

When it comes to coils for rebuildables the wattage isn't as critical, I suggest you start at around 12 Watts and slowly raise the wattage if you find it doesn't give enough vape or is too cool a temperature until you find your preference. As a rough guess I'd say somewhere in the 12 to 16 Watt range would suit most MTL vapers but you can go higher if you like a higher powered lose MTL. With rebuildables it's not a complete loss if you overdo it slightly - you may scorch the cotton if you go OTT, but its highly unlikely you'll damage the coil - only the cotton needs replacing, unlike a stock coil when any hint of burnt cotton means you have to bin it.

Thank you

 

[Simebaby]

Another vote for the Pandora here - very forgiving, and superb flavour. The Neeko which @rew mentioned is also a cracking tank and easy to build.
I tend to use 27awg wire, 5 wraps with a 2.5mm inner diameter gives me around 0.75-0.8ohms.
The Cthulhu Artemis is also a great tank, but a bit more fiddly than the two above,

 

[Eka]

Another vote for the Pandora here - very forgiving, and superb flavour. The Neeko which @rew mentioned is also a cracking tank and easy to build.
I tend to use 27awg wire, 5 wraps with a 2.5mm inner diameter gives me around 0.75-0.8ohms.
The Cthulhu Artemis is also a great tank, but a bit more fiddly than the two above,

Thank you

 

[Crispycritters]

Just would like to say a big thank you all who write a reply with all this helpful information and suggestions . I am still looking at tanks and as soon I will buy it I will get the all the bits and bobs for it and I will start to build my own coils as how I said I fed up with stock coils as couple of times I got a bad batch and they awful. I am really looking at
Reload MTL RTA 22mm.
Any suggestions?

I have a clone version of this. The airflow under the coil is shaped like a shower head with larger central hole surrounded by 6? smaller ones.

I love this tank with the airflow ring opened up running at about 25 Watts for a restricted DL vape, but I can't get a decent vape out of it at MTL settings - the flavour seems muted to me at anything under 20 Watts. I think the shower head type under coil disperses the air too much and instead of the airflow hitting the centre of the underside of the coil with pressure it is too dispersed. Admittedly I have a clone version - but the dimensions should be identical to the original.

I'm only an occasional MTL vaper so I don't feel qualified to give any recommendations about which tanks are the best, but out of the 3 MTL tanks I own this is my least favourite. Its great for RDL, but when it comes to MTL I can't get too excited about it.

 

[Giurra]

Thank you for your reply.
I was looking for a pre made coils and I find on Manabush website Vandy Vape
10 x 0.74Ohm Fused MTL Clapton Coils are they 0.7? And where I can found the range of wats to use, usually It’s on the stock coil packet . 10-15 w?
Also this coils is 2.5 mm and I learn here from some kind person who explained me about the cotton, that I will buy shoelaces pre made cotton for 2.5 mm.
I will start with the pre made coils but I ideally would like to have a master class with someone who knows all about it to learn how to make them my own, as I don’t want to blow up the whole lot . I am really don’t understand them ohm to wattage etc.

@Crispycritters explained this nicely. Nothing more to add to it

 

[LordOdin]

Got a 0.68 Staple in my Pandora and running it at 23w and the Vape and Flavour are the best i have had from a MTL Tank.

 

[Eka]

I have a clone version of this. The airflow under the coil is shaped like a shower head with larger central hole surrounded by 6? smaller ones.

I love this tank with the airflow ring opened up running at about 25 Watts for a restricted DL vape, but I can't get a decent vape out of it at MTL settings - the flavour seems muted to me at anything under 20 Watts. I think the shower head type under coil disperses the air too much and instead of the airflow hitting the centre of the underside of the coil with pressure it is too dispersed. Admittedly I have a clone version - but the dimensions should be identical to the original.

I'm only an occasional MTL vaper so I don't feel qualified to give any recommendations about which tanks are the best, but out of the 3 MTL tanks I own this is my least favourite. Its great for RDL, but when it comes to MTL I can't get too excited about it.

Thank you.
I think I will go with the Vandy Vape Berserker V2 .
Very helpful comment.

 

[LordOdin]

Got a 0.68 Staple in my Pandora and running it at 23w and the Vape and Flavour are the best i have had from a MTL Tank.

EDIT To Add : I had to take a loop out and it's at 0.45 ohms.