Silica Wick & Kanthal Wire guide/starter kit suggestions..??

[vaporsizer]

 

[Ditch]

All my evods have Kangertech evod marked on the base, got them here. Never leaked.

http://myepack.co.uk/clearomizers/evod-clearomizer-ss.html

I have just studied that picture and they look identical inside and out, but no Kangertech markings, as it says they are 2.5 Ohms standard I just checked mine on my Vamo5 and got a 2.3 a 2.4 another 2.4 a 2.7 and two 2.8.. not a single 2.5 so maybe they are just cheap n nasty..

 

[vaporsizer]

I have just studied that picture and they look identical inside and out, but no Kangertech markings, as it says they are 2.5 Ohms standard I just checked mine on my Vamo5 and got a 2.3 a 2.4 another 2.4 a 2.7 and two 2.8.. not a single 2.5 so maybe they are just cheap n nasty..

Think that the kanger atomizer heads are only marked with the resistance value.

 

[Miss Pepper]

Are the coils tight in the tank? Because if not that would make the juice piss out the bottom

 

[vaporsizer]

Are the coils tight in the tank? Because if not that would make the juice piss out the bottom

Can you say exactly what you mean by that Pep' !

 

[Miss Pepper]

Can you say exactly what you mean by that Pep' !

Just a suggestion as ive not had any probs with my evods / copies

When putting a replacement coil into the ring, screw it in tight. Add the now two part section to the battery. Take tank and turn upside down. Add liquids to the insides of the tank, careful not to get it into the smaller middle tube. Keep tank upside down and attach battery / coil set up to take. Tighten.

Turn right way round. Get bit of tissue and roll into a twisted dipper. Put into mouth piece twisting as you push it in further till it wont go any further. Keep twisting while slowly pulling back out. Turn tissue round and repeat process. This soaks up juice that got into the inny tube.
Couple of presses on the button to get the juice warm and flowing then vape away.

Better vaporsizer

 

[Ditch]

Are the coils tight in the tank? Because if not that would make the juice piss out the bottom

Ermmmmm.. They are screwed in tight to the base & the chimney is pressed in well, I have tried adding extra flavour wick from one of the others and removing some.. I have tried not pushing the top silicon cap all the way down as suggested in a youtube video, it pours out of the center hole (well enthusiastic drips lol)..

I have just checked and there is no resistance printed on the coil head, so I presume they are fake/moody..

Really don't want to piss off the only bricks and mortar around here, but I think I should chuck them back at them, considering I can buy genuine ones online for less money.. live n learn I suppose..

 

[vaporsizer]

Just a suggestion as ive not had any probs with my evods / copies

When putting a replacement coil into the ring, screw it in tight. Add the now two part section to the battery. Take tank and turn upside down. Add liquids to the insides of the tank, careful not to get it into the smaller middle tube. Keep tank upside down and attach battery / coil set up to take. Tighten.

Turn right way round. Get bit of tissue and roll into a twisted dipper. Put into mouth piece twisting as you push it in further till it wont go any further. Keep twisting while slowly pulling back out. Turn tissue round and repeat process. This soaks up juice that got into the inny tube.
Couple of presses on the button to get the juice warm and flowing then vape away.

Better vaporsizer

Haha, nah, i prefer the short version. Hehe, was only kiddin' likey. Cheers.

 

[vaporsizer]

Ermmmmm.. They are screwed in tight to the base & the chimney is pressed in well, I have tried adding extra flavour wick from one of the others and removing some.. I have tried not pushing the top silicon cap all the way down as suggested in a youtube video, it pours out of the center hole (well enthusiastic drips lol)..

I have just checked and there is no resistance printed on the coil head, so I presume they are fake/moody..

Really don't want to piss off the only bricks and mortar around here, but I think I should chuck them back at them, considering I can buy genuine ones online for less money.. live n learn I suppose..

If they're fakes & you thought they were real kangas then yeah, take 'em back. Tell 'em they're crud & get a refund.

 

[Ditch]

If they're fakes & you thought they were real kangas then yeah, take 'em back. Tell 'em they're crud & get a refund.

They were just in the same display case as the Kangertech stuff.. it was more of a presumption than a big sign saying they were something they ain't.. but there is a bloody great Kangertech sticker on the display case lol..

They are new (open two weeks tomorrow) and were extremely friendly and very helpful to be truthful, I am 100% sure that they will help me sort the problem.. will see if I am as positive about them this time tomorrow lmao..