Snapdragon v1.5

[mcboffin]

I use a regulated build of 0.4mm 9 wraps 3mm ID coming out at 0.67ish.

Did you ever get it all tightened down properly and could that be causing the resistance change?

I figured out I'm missing an o ring off the bottom of the negative post. Going to strip it and reassemble tonight

#ShouldHaveGotAPredatorInstead.

 

[mcboffin]

Seems much better with the o ring on the bottom of the negative :-)

 

[mcboffin]

Stunning Vape. 2 air holes open - Figleys Owd Smokey.

The only downside is the small pool of condensed juice in the stock drip tip.

Anyone know where I can get a more open white teflon or delrin tip? The derringer tips fit and are much more open but they're a tad on the short side.

 

[stevoknevo]

Stunning Vape. 2 air holes open - Figleys Owd Smokey.

The only downside is the small pool of condensed juice in the stock drip tip.

Anyone know where I can get a more open white teflon or delrin tip? The derringer tips fit and are much more open but they're a tad on the short side.

Success at last! Can't help on the drip tip front as I use the standard one; as you noted it does pool liquid slightly but I find it doesn't gurgle or owt. I was using a drip tip I had lying about but it was drawing liquid in to my mouth on the squonker (same tip was fine on the non b/f one I had previously) so I reverted to the standard. Have a couple of the longer v2 drip tips coming from Eden Mods, see how they are, but I do fancy one of Vince's.

 

[mcboffin]

Success at last! Can't help on the drip tip front as I use the standard one; as you noted it does pool liquid slightly but I find it doesn't gurgle or owt. I was using a drip tip I had lying about but it was drawing liquid in to my mouth on the squonker (same tip was fine on the non b/f one I had previously) so I reverted to the standard. Have a couple of the longer v2 drip tips coming from Eden Mods, see how they are, but I do fancy one of Vince's.

I bet you'll know....


For squonking, is it as simple as:

1. Take 510 pin out.
2. Install BF pin
3. You're ready to Squonk?

(Obviously with step 3 there's putting it on and atty, etc etc).

Ta.

 

[stevoknevo]

I bet you'll know....


For squonking, is it as simple as:

1. Take 510 pin out.
2. Install BF pin
3. You're ready to Squonk?

(Obviously with step 3 there's putting it on and atty, etc etc).

Ta.

Should be G. I have a v1 which is a dedicated BF, but it should be a simple case of removing the 510 pin and fitting the BF pin.

 

[mcboffin]

Should be G. I have a v1 which is a dedicated BF, but it should be a simple case of removing the 510 pin and fitting the BF pin.

Ta. It's on the Paps at the moment and moving to its permanent home on the Mushroom when that arrives this week.

 

[TruckinVaper]

Ta. It's on the Paps at the moment and moving to its permanent home on the Mushroom when that arrives this week.

It is as easy as that.

What batch of yours from? B1 had a very simple squonk pin, basically just a long hollow grub screw. It worked ok but could be a bit wobbly and could screw itself back in when screwing the atty down. B2 has a much better squonk pin, it's got a head to it and also a small o ring, stays put much better. They made the pin available on it's own for people with the B1.

 

[mcboffin]

I've got the b2 one - should be good to go soon. Not that I'm F5ing the tracking site yet though.

 

[mcboffin]

Just checking. Is there something I need to do with the o ring on the standard 510 before swapping over to the BF pin?

Looks like tomorrow is mushroom day.