What's new

What do I need to buy

rtni said:
If your mods have a 510 slot (I haven't seen any that aren't) then any tank with a 510 connecting pin will fit - the troll, OBS engine and the nano all certainly do. Great tanks BTW. I have all three although I have't tried the troll yet.

Batteries:

I would research into batteries and battery safety (if you haven't already) and if I could give you any advice, definitely don't skimp on them - get them from a genuine seller and look after them and always keep them in their protective cases. Don't forget to take them out of your mods when you're going to bed. If you look after them and keep them paired, you should get about 300 charge / discharge cycles from them. Since they are cheap, I'll usually bin them after a year anyway (but that's just me). Get yourself a few spares batteries btw. I think I have about 20 batteries now and I really only charge once a week.

http://www.instructables.com/id/How-to-Prolong-the-Life-of-an-18650-Battery/

I only purchase from fogstar and wait until Fridays when they run their sale - they have a selection of chargers listed there too. Considering they take batteries very seriously, you could assume they treat the chargers the same. I personally have a nitecore D4 (4 cell charger) and an i8 (8 cell charger). An i8 might be overkill for you.

Cotton:

Cotton bacon v2, native wicks or kendo gold edition. I tend to stick with cotton bacon - as for how much you use, well that depends on what tank your using (single or dual coil), if your dripping / testing juice etc and your general vaping habits. 90 minutes vaping a day, you'd stretch a packet of cotton bacon quite far. No harm stocking up on a few packs. People say cotton is cotton and they are probably right - I just stick with what I know. One day I'll buy a huge bulk pack from China like some folk do :)

Wire:

You've a few choices depending on what you want to do - you can buy wire and make your own coils or just buy pre made coils - the later obviously being less hassle but more expensive. You could start with some basic kanthal wire until you get familiar with coil building and move onto the more expensive wire types. I use:

https://www.wireandstuff.co.uk/products/Vaping-Wire.html

Amazon have large boxes of pre built coils (such as demon killer etc) that will allow you to experiment for little money. I still use them when I'm dripping to test juices.

If you want to dive straight into sampling some of the best coils then get in touch with @Smut. His coils are fantastic and will last me a month (I do vape a lot) with the odd dry burn. I also use runnynose coils which are of similar quality. My local vape shop stock them so it's easy picking some up in town when I'm driving through.

Remember to check the vendors section for reliable sources in the UK to get all your gear from

Trying to think what else you need... A dripper is great when you're at home and trying out a few different juices. You could get yourself an authentic wasp nano for around £15 or a Hadaly or a Narda clone from fasttech.

The coil master kit is handy but you could simply get the individual items separately if you want to save some money. The two most useful items in the kit are the ohm reader (although it's pretty basic) and the coil jig / wand.

Sorry for my ramble back but I hope this helped :)
Click to expand...
Loads of great info! Thanks :)
 
just a quick thing about the coil master kit, I was looking round to buy bits and pieces instead of the kit last weekend because i have most of the stuff in it (who hasn't got scissors?) but the main three things were the ohmmeter, the coiling jig and the tiny side cutters. I couldn't source those for less than £28 combined (with postage), so the coil master kit for £30 off ebay with the extra bits i didn't need (and cotton and wire) for me was a good deal. wouldn't have paid £40 for it though.
 
ObiWanVaponi said:
just a quick thing about the coil master kit, I was looking round to buy bits and pieces instead of the kit last weekend because i have most of the stuff in it (who hasn't got scissors?) but the main three things were the ohmmeter, the coiling jig and the tiny side cutters. I couldn't source those for less than £28 combined (with postage), so the coil master kit for £30 off ebay with the extra bits i didn't need (and cotton and wire) for me was a good deal. wouldn't have paid £40 for it though.
Click to expand...
The V3 kit I got from Amazon came with the new V4 coil jig which apparently is loads better. Also came with some wire rods, dunno what they're for lol
 
Jackymax said:
The V3 kit I got from Amazon came with the new V4 coil jig which apparently is loads better. Also came with some wire rods, dunno what they're for lol
Click to expand...
yeah mine came with v4 jig. no wire rods though. maybe they're for coils? not that advanced yet.
 
Jackymax said:
The V3 kit I got from Amazon came with the new V4 coil jig which apparently is loads better. Also came with some wire rods, dunno what they're for lol
Click to expand...
Making coils ;). When class is paying attention I'll continue :rotflmao:
 
You must log in or register to reply here.

Similar threads

B
Really need your help!
2 3 4
Replies
33
Views
1K
Barbyery
B
S
Innokin Endura T18ii frankenstein!!
Replies
3
Views
208
MrDJ
MrDJ
X
What am I doing wrong?
Replies
3
Views
758
Netvaper
Netvaper
B
I don't really know what I'm doing!
Replies
8
Views
581
BobbyT
B
D
Need help with mod issues
Replies
1
Views
527
Crispycritters
C
Back
Top Bottom