Nife 30 wire help

[witt15]

So I'm not new to building, but I am new to tc, I've heard the hype for the nife wire which I wanna use to do a build in the aromamizer using a snow wolf or ipv4s . Any advise on gauge to order and a good build to start with would be appreciated. Thanks

 

[Tubbyengineer]

So I'm not new to building, but I am new to tc, I've heard the hype for the nife wire which I wanna use to do a build in the aromamizer using a snow wolf or ipv4s . Any advise on gauge to order and a good build to start with would be appreciated. Thanks

).32 or 0.40 either will do, a standard spaced coil is the easiest to get right, start with that and you can try some of the other styles of build later...

 

[witt15]

Thanks I'll give it a go, would you start with standard or vertical, I have done kanthal vertical without leaking but know the wicking may be different. Thanks again

 

[Mr Numpty]

Thanks I'll give it a go, would you start with standard or vertical, I have done kanthal vertical without leaking but know the wicking may be different. Thanks again

Both are fine. I've been using horizontal coils in the RDTA recently as it cuts the airflow down just a smidge over verticals, but verticals are great in it of course.
29 gauge Stealth Vape NiFe, 8 wraps using 3 mm ID came in at the 0.15 I build all my TC coils at. Vaping nice.

 

[witt15]

Both are fine. I've been using horizontal coils in the RDTA recently as it cuts the airflow down just a smidge over verticals, but verticals are great in it of course.
29 gauge Stealth Vape NiFe, 8 wraps using 3 mm ID came in at the 0.15 I build all my TC coils at. Vaping nice.

Wicked I like your style my wire came today so guess I'll be busy tonight, cheers for info @Mr Numpty and as regards the D1 still not shipped[emoji26]. Guess will be nice surprise when it finally arrives

 

[longy01]

Both are fine. I've been using horizontal coils in the RDTA recently as it cuts the airflow down just a smidge over verticals, but verticals are great in it of course.
29 gauge Stealth Vape NiFe, 8 wraps using 3 mm ID came in at the 0.15 I build all my TC coils at. Vaping nice.

@MrNumpty. Will have to agree with you on this. Tried a NiFe Single vertical coil this afternoon. Must admit, I found the vape to be off balance if that makes any sense. Very airy but hot at the same time. Prefer my vape to be warm and saturated. Stuck a pair of horizontal coils back in. Like you say, even using the rdta without airflow control, it's a more restricted draw. More to my liking.

 

[witt15]

Thumbs up[emoji106]@MrNumpty, my 1st horizontal build in RDTA and my 1st build using NiFe, followed instructions as listed

Works a treat even at 350 degrees with my red Astaire, time to sit back and chill. Thanks it's saved me a lot of trail and error[emoji1]

 

[longy01]

Thumbs up[emoji106]@MrNumpty, my 1st horizontal build in RDTA and my 1st build using NiFe, followed instructions as listed View attachment 69702
View attachment 69703
Works a treat even at 350 degrees with my red Astaire, time to sit back and chill. Thanks it's saved me a lot of trail and error[emoji1]

Very nice m8. Enjoy

 

[Mr Numpty]

Works a treat even at 350 degrees with my red Astaire, time to sit back and chill. Thanks it's saved me a lot of trail and error[emoji1]

Woo yeah! Nice job. Enjoy.

 

[witt15]

Thanks guys I will[emoji1]